If the washer is not spinning, the next check is of the washer control magnet. Washers use a control magnet, an electrical-mechanical component, to enable the gearcase to shift into the spin cycle. You can easily check the control magnet by using the volt/ohmmeter set on the RX-10 scale. With the volt/ohmmeter on RX-10 scale, connect the probes to both terminals of the control magnet. NOTE: When checking a suspected faulty control magnet, remove the wires from the washer wiring harness to avoid an inaccurate reading. Read the rest of this entry »
Specific failure symptoms include: 1) When the washer is turned ON, nothing happens. 2) When the washer is turned ON you hear a faint “buzz.”
To find the cause of this problem, first check to be sure that the washer is plugged in a working power source.
Make a line voltage check at the washer receptacle to determine if the problem is a faulty power receptacle or a problem within the washer. Make a voltage line check by setting the volt/ohmmeter on the 150 A/C scale and placing the probes in the holes of the wall receptacle. The meter should read 110-125 volts. Read the rest of this entry »
This failure is normally attributed to a loss of electrical power or an electrical overload.
To find the cause of the problem, move the dryer out from the wall and unplug the dryer power cord from dryer wall receptacle. Make a voltage check with the volt/ohmmeter to determine if there is electrical power available to the dryer receptacle or to the dryer power cord.
To avoid incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter before making continuity checks. See operating instructions that came with your volt/ohmmeter. Read the rest of this entry »
The home repairmen should be very cautious when it comes to repair of the household refrigerator. They should be aware of the fact that they are dealing with a very expensive product, and one that contains a very delicately balanced cooling system. One small error could damage the system beyond repair.
Replacing a faulty compressor requires special vacuum and freon filling equipment that only professional technicians can handle.
The refrigerator cooling system is not like the family automobile air conditioner. You can’t simply attach a hose and add a little freon when it isn’t cooling properly. The refrigerator is a carefully balanced, sealed system, and normally should not have a freon-loss problem. If the unit is not cooling properly, and you have determined that the compressor is running, then there are several electrical components in the system that could be at fault. Read the rest of this entry »
There are three types of failures that are associated with the Fridge start capacitor. These failures are a defective capacitor. an open filament capacitor, and a grounded capacitor. You can check each of the above failures with the volt/ohmmeter. First, unplug the Fridge power cord. Using hand tools, remove the screws that secure the Fridge back and remove the starting capacitor from the compressor starting package. Look for traces of oil on or around the capacitor. If oil is present, the capacitor is defective.
CAUTION: A charged capacitor is extremely dangerous. A capacitor that has been removed from the compressor starting package will hold a charge indefinitely, even when not in use. If you touch the terminals of a charged capacitor, the built-up voltage could give a high-voltage shock that could be fatal. A flat-blade screwdriver across the terminals should be used to discharge a capacitor. Read the rest of this entry »
Move the refrigerator out from the wall. Unplug the refrigerator power cord, and turn OFF the water supply to the icemaker.
Using hand tools, remove screws and discard the defective water supply valve. When installing a water supply valve on the water heater, install only on the cold-water side of the water heater. Read the rest of this entry »
If an appliance needs inspection, unplug it from the socket. No, don’t just turn off the switch — there may still be some current flowing.
When working on switches, sockets or, simply said, things that cannot be removed from the energy source, switch off the power at the main switch on the electrical switch board. To be on the even safer side, always wear rubber-soled shoes (only during the repair); it will reduce the shock should all your safety precautions fail (turning you into a fruitcake as opposed to a full-blown vegetable). Read the rest of this entry »
There are some things you can do to prolong the life of your appliances and save endless hours of frustration, burning toast, getting marks on your favourite white shirt and taking melted ice-cream out of the freezer. As with many other things in life, appliances need looking after. Do this well and they will serve you faithfully.
There are too many brands of washing machines available to mention, old and new, but they all have two basic requirements to operate: they need water and they need power. This is one of those appliances where the manual comes in very handy. Read the rest of this entry »
Portable electric heaters and many fixed electric heaters are controlled by a switch or switches mounted on the frame of the heater. In addition, the heater is switched at a switched socket-outlet or switched fused connection unit or is connected to a non-switched socket-outlet which means pulling out the plug to switch off the heater.
Wall panel heaters, oil filled radiators, convectors and other heaters operating at ‘black heat’ have an integral thermostat which is set to the required room temperature. Read the rest of this entry »
Capacitors used for motor starting may have metal or plastic outer casings with an insulated top with two terminals. Internally the two terminals are connected to two sheets of metal foil with an insulator between. This package of large surface area is rolled into a cylinder which fits into the shell of the capacitor. As the voltage supplied to one terminal is alternating (at 50 times per second), so does the polarity of its connected foil. An opposite movement of electrons is induced in the other foil, even though they are insulated electrically. This causes a delay in the electrical path, and this, in the case of an asynchronous induction motor, gives the outof-phase feed to the start winding. Read the rest of this entry »
