This failure is normally attributed to a loss of electrical power or an electrical overload.
To find the cause of the problem, move the dryer out from the wall and unplug the dryer power cord from dryer wall receptacle. Make a voltage check with the volt/ohmmeter to determine if there is electrical power available to the dryer receptacle or to the dryer power cord.
To avoid incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter before making continuity checks. See operating instructions that came with your volt/ohmmeter. Read the rest of this entry »
Unplug the power cord or gas supply before servicing the clothes dryer. Move clothes dryer out from the wall. Exercise care when moving the dryer from its original position because the dryer legs can easily tear holes in your floor.
Remove screws to dryer top. Lift the top of the dryer by inserting a flat-blade screwdriver between the cabinet and the top of the dryer. Remove the screws that secure door switch to dryer front panel and discard the door switch. Read the rest of this entry »
Yes, you too can be the proud owner of a home-entertainment system and it doesn’t have to cost you a small fortune. If you have ever wondered how your mates get to have sound booming from seemingly every corner of the house when merely watching TV, we have the answer (naturally!). All you need to do is connect your TV to your video machine to your Hi-fi (these don’t have to be top of the range) after having acquired a couple of cables to make all the connecting possible.
You WILL NEED
(This will vary depending on what it is that you are connecting to what.) Read the rest of this entry »
The information given here also applies to the grills on many cookers. This is a simple way to ascertain if the control is faulty. Short circuit failures on elements may damage regulators in which case, if you are in any doubt, renew it.
The following test is for a single circuit application, that is, a single element. For double regulators, that is, a double element, the same procedure will be required on both single and double operations of the switch. From off position an anticlockwise turn will put into circuit one element (usually the inner), a clockwise turn from the off position will put into circuit both inner and outer. Check that double regulators operate independently on a half turn each. For singles, use ony a full turn. Read the rest of this entry »
These are among the most frequently used items in the home. Generally, they are very reliable, but when a problem does occur, it is usually at the most inconvenient time. Over the years, ovens and hobs have become increasingly complex with the addition of digital timers, touch controls and other refinements.
It is essential to remember that these appliances are connected directly to the mains supply and, as with any repair, cleaning or service, must be completely isolated. In this instance, the main double-pole isolation switch for the appliance must be switched off and also the fuse for the cooker/hob circuit removed from the main distribution board. If an MCB is fitted in place of a fuse, ensure it is in the off position. Do not proceed with any repair or service if both these requirements are not met and also make sure you advise others who may use the switch of your intentions. Read the rest of this entry »
Throughout this post, references are made to meters and their use in continuity testing of individual parts of the appliances and their connecting wires. All testing and checking for ‘open’ (not allowing for current flow) or `closed’ circuit (allowing current to flow) must be carried out using a battery-powered multimeter or test meter. Testing should never be carried out on live items under any circumstances. Appliances must be disconnected from the mains supply. Read the rest of this entry »
The toaster is another appliance that uses heating elements and, in most instances, a bi-metal strip thermostat to control the length of time the bread is exposed to them. This, in turn, relates to the degree of browning required by varying the position of the bi-metal contact points. When bread is inserted, a latched spring system is actuated to hold the bread carrier in place. At the same time, it makes a switch contact to supply power to the elements. The heat from the elements toasts the bread and also heats the bi-metal strip, causing it to bend. Read the rest of this entry »
There are no faults with CD players that are within the capabilities of the D-I-Y repairer. Do not attempt adjustment or servicing to any internal components; leave it to a trained service engineer. However, looking after your equipment properly minimizes the possibility of faults occurring.
The first consideration is the positioning and environment of the player. Do not place a CD unit in strong sunlight, near heat or in damp or humid conditions. The CD system requires very close tolerances to be maintained for accurate disc reading and sound reproduction. Read the rest of this entry »
The brush roll is supported on bearings at each end so the barrel rotates freely. Types of bearings, barrels and brushes differ from model to model as well as between manufacturers. Some manufacturers supply individual parts for the brush roll, such as brush strips, bearings and barrel; others supply only complete assemblies. The brush roll on some models may have removable brush strips, whereas others may be a solid brush roll of wood or plastic with fixed brushes. A small selection is shown here to highlight the differences. Read the rest of this entry »
The upright style of vacuum cleaner is perhaps the best for large areas of carpet. It is especially good at removing dirt embedded within the pile and pet hairs from the surface, even on sculptured carpets. A drawback with the basic upright cleaner is its difficulty with cleaning stairs. The problem has been overcome with the modern combination of upright and cylinder cleaner. This type may be the best option if you have large areas of fitted carpet and staircases. The motor within the upright cleaner creates the airflow (suction) and drives a rotating brush roll, often called an agitator barrel. Read the rest of this entry »
