If the washer is not spinning, the next check is of the washer control magnet. Washers use a control magnet, an electrical-mechanical component, to enable the gearcase to shift into the spin cycle. You can easily check the control magnet by using the volt/ohmmeter set on the RX-10 scale. With the volt/ohmmeter on RX-10 scale, connect the probes to both terminals of the control magnet. NOTE: When checking a suspected faulty control magnet, remove the wires from the washer wiring harness to avoid an inaccurate reading. Read the rest of this entry »
Other specific symptoms include: 1) Food not remaining at desired temperature. 2) Compressor does not cycle ON.
Because the interior light is ON, the Fridge has the required electric power to operate.
Something is causing the compressor not to cycle ON. Check the components in the order that they are listed below. The most likely component at fault is the defrost timer, which could be stuck in the defrost cycle. The Fridge is then in a permanent state of defrost and does not cycle ON. However, if the compressor tries to start and the interior light dims, the problem is probably not the defrost timer or the thermostat; therefore, check the components of the compressor assembly starting with the starting relay. Read the rest of this entry »
Some fluorescent fittings have no starter switch(s) for the tubes. Instead there is S transformer to provide the prewarming and the tube itself has a metal stripe running throughout its length from one lamp cap to the other. The lamp caps are earthed at the lampholders.
This assists in the starting of the electron flow and, as there is no starter to operate, the lamp strikes without the characteristic delay of the switch-start type.
A fluorescent tube has an expected life of 5000 to 7000 light hours or up to seven times that of an electric light bulb. Read the rest of this entry »
Plain and twisted candle lamps are made in 25 W, 40 W and 60 W sizes and in pearl, plain, amber and silvered colours. They are made in be (bayonet cap) and sbc (small bayonet cap) versions.
These are used for wall lights and for period pendant fittings.
These are sometimes called ’strip lights‘ and are non-fluorescent, being tungsten filament lamps. There are two versions, one type is commonly used for applications in the home, and the second type is known as architectural lamps‘. Read the rest of this entry »
A radial power circuit is the name given to a circuit supplying a number of 13 A socket-outlets and fixed appliances using one cable which is not wired in the form of a ring but terminates at the last outlet.
The permitted number of socket-outlets (and fixed appliances) depends on the current rating of the circuit which can be either 20 A, wired in 2.5 mm2 cable, or 30 A wired in 4 mm2 cable. The number of socket-outlets and fixed appliances which can be served by a 20 A radial circuit depends also on the location of the circuit and whether the outlets are confined to one room. Read the rest of this entry »
If an appliance needs inspection, unplug it from the socket. No, don’t just turn off the switch — there may still be some current flowing.
When working on switches, sockets or, simply said, things that cannot be removed from the energy source, switch off the power at the main switch on the electrical switch board. To be on the even safer side, always wear rubber-soled shoes (only during the repair); it will reduce the shock should all your safety precautions fail (turning you into a fruitcake as opposed to a full-blown vegetable). Read the rest of this entry »
Joint boxes are usually circular and for part of the circuit wiring. They are fix permanently to the house structure are used principally in lighting circuits. Join boxes are available in 4- 5- and 6-terminal versions.
A 3-terminal joint box of 30 A current rating is used for ring circuits to connect spur cables to the ring cable, as shown the illustration. Read the rest of this entry »
Specific failure symptoms include: 1) Water on floor near dishwasher. 2) During dishwasher cycle, water accumulates on left or right side of dishwasher lower panel.
To locate the cause of the problem, remove lower panel and check for broken plumbing drain connections, water inlet valve, broken or cracked hoses (drain and inlet), or drive motor and pump assembly motor seal. If a hose or a faulty part is found, replace it. Check that door is closing properly. Read the rest of this entry »
Table lamps, floor standards, bedside lights and other portable lights can have dimmer control using any one of three methods. One method is a dimmer socket adaptor which plugs into the standard 13 A socket-outlet. This unit has two 2-pin sockets and is especially suitable for controlling two bedside lamps in a twin-bedded or a double-bedded room. The control knob on the adaptor dims both lamps at the same light intensity; they cannot be controlled independently.
Another method uses a line-cord dimmer which is wired into the flex of the lamp. The dimmer can be a standard wall type mounted on a plastic box and placed on the arm of the chair, table, desk, or any other chosen position. Alternatively, it can be a mini-dimmer switch resembling a torpedo table lamp switch. This type is especially suitable for the individual control of bedside lamps. Read the rest of this entry »
