Clothes dryers accomplish their task by furnishing heated air in large volumes to the interior of a rotating drum where the clothes are tumbled and tossed while being exposed to the passing air. For the clothes dryer to work, the machine needs a source of heat, tumbling capability, large volumes of fresh air, and the ability to remove large amounts of moisture-laden air from the interior of the dryer cabinet. Read the rest of this entry »
The home repairmen should be very cautious when it comes to repair of the household refrigerator. They should be aware of the fact that they are dealing with a very expensive product, and one that contains a very delicately balanced cooling system. One small error could damage the system beyond repair.
Replacing a faulty compressor requires special vacuum and freon filling equipment that only professional technicians can handle.
The refrigerator cooling system is not like the family automobile air conditioner. You can’t simply attach a hose and add a little freon when it isn’t cooling properly. The refrigerator is a carefully balanced, sealed system, and normally should not have a freon-loss problem. If the unit is not cooling properly, and you have determined that the compressor is running, then there are several electrical components in the system that could be at fault. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use extreme care when moving the Fridge, because the Fridge legs can easily damage the floor.
Open the Fridge door and locate the control console in the back of the Fridge cabinet. Remove the screws that secure the console cover. Remove the thermostat bracket. NOTE: Before removing the defrost timer from the Fridge cabinet, mark the wires, so they can be replaced correctly on the replacement part. Next, remove the screws that secure the defrost timer to the Fridge cabinet. Next, remove wiring harness and remove defrost timer. Read the rest of this entry »
Unplug the fridge power cord before servicing the fridge. Move the fridge out from the wall. Use extreme care when moving the fridge, because the fridge legs can tear or damage the floor.
Using hand tools, remove the screws on all four sides of the fridge or freezer doors so that you can remove and discard the defective gasket(s). Before removing the old gasket, note carefully how the gasket is installed, because the replacement gasket has to be installed in the same position as the defective gasket that is removed. Before installing the replacement gasket, heat the rubber with a home hair dryer set on low heat. This will make the rubber more flexible,’ and easier to install on the fridge or freezer door. Install the replacement door gasket by mounting the lip of the gasket under the retainer plate. Read the rest of this entry »
Other specific failure symptoms include: 1) Food not remaining at the desired temperature. 2) Fridge compressor does not cycle OFF.
If the compressor motor runs continuously in an attempt to keep the fridge cool but the cabinet is still not cool enough, you will have to find the component or failure that is restricting the cooling capacity of the fridge. Check the components in the order that they are listed below. Read the rest of this entry »
Specific symptoms include: 1) Compressor motor runs all the time and does not cycle regularly. 2) Food freezing in the fridge section of the fridge. To find the cause of this problem, which is usually caused by a faulty thermostat, move the fridge out from the wall and unplug the fridge power cord.
Unplug the fridge power cord before servicing the fridge. Move the fridge out from the wall. Use extreme care when moving the fridge because the fridge feet can damage the floor. Read the rest of this entry »
Turn OFF the electricity at the circuit breaker panelbefore servicing the dishwasher. Exercise care when moving the dishwasher from its space. The leveling legs can easily damage the floor.
Turn OFF the electricity at the circuit breaker panel. Remove the screws that secure the lower panel to the dishwasher cabinet. Disconnect the drive motor connector from the harness wiring. Remove the hose clamp from drain hose that is secured to drive motor base coupling. Remove drain hose from coupling. NOTE: When removing drain hose, place a small pan or towel under the motor base coupling. It is possible that when hose is removed water could spill onto the floor. Read the rest of this entry »
