This valve assembly is probably the most important component of the gas burner assembly. The valve assembly controls the flow of gas to the main burner from the gas supply line.
Cycling thermostats are bi-metal devices or thermo-discs that are designed to cut the main burner OFF when a pre-determined temperature has been attained in the dryer drum. There is no adjustment of the temperature response of these thermostats. Read the rest of this entry »
If the heating element tests OK, you should next check all the electrical wiring from the dryer timer assembly, thermostats, and drive motor. Electrical wiring in a dryer becomes brittle and burned because of the excessive heat. To locate defects in the wiring, use a volt/ohmmeter to make continuity checks on wires that you suspect are faulty.
The problem of no heat in the gas dryer is much the same as the electric dryer, except that instead of checking for a possible defective heating element, you must check the gas ignition circuit. A sure and simple test is check voltage to the gas burner wiring harness. Read the rest of this entry »
Specific failure symptoms include: 1) Clothes are not dry at end of cycle. 2) The dryer timer assembly is not advancing in the cycle properly.
To find the cause of the problem, first move the dryer out from the wall and remove the vent hose. With the dryer running, place your hand on the dryer exhaust duct to determine if there is any hot air being discharged. If the air is cold, you will have to make a line voltage check at the dryer receptacle to determine whether full 220-to-240-volt power is available. Read the rest of this entry »
Electric heating of water can be carried out in a variety of ways. These include small capacity heaters fitted above the sink, instantaneous sink heaters or immersion heaters in the hot water tank.
Small storage water heaters fitted over the sink or washbasin having capacities of up to about 3 gallons and electrical loadings of 1 to 3 kW are usually supplied from the ring circuit by means of a spur. Except in a bathroom, the outlet can be a fused plug and switched socket-outlet, preferably with neon indicator. Read the rest of this entry »
Specific failure symptoms include: 1) Dishwasher stops before the drying cycle. 2) The dishes are not dry when removed from the dishwasher.
When this problem is noticed, it is often not the fault of the dishwasher. The homeowner simply did not close the dishwasher door. A partially closed door will prevent the dishwasher from making electrical contact. When closing the door, make sure that the door shuts properly before starting the dishwasher. Read the rest of this entry »
Do not fit a high wattage bulb into a shade or fitting designed for bulbs of lower ratings. Some shades give the maximum wattage but if there is no indication, restrict the wattage to 60 W or preferably 40 W. Otherwise overheating may occur and the shade material either melt or ignite. Damage can also be done to the fixed wiring by transference of heat through the lamp- holders; this is particularly the case if it is a close ceiling fitting. Damage can also be done to the flex, if pendant and the flex is not of the heat-resisting type. Read the rest of this entry »
A huge variety of household appliances contain heating elements. The two basic types are the exposed single-wire element, most often used in hairdryers, fan heaters and toasters, and the metal-sheathed element used in ovens, grills, iron sole plates and immersion heaters.
This type of element is simply an exposed length of conductor which heats up when a current is passed along it due to the resistance properties of wire. As it is an exposed conductor, it must be housed and supported in a way that avoids accidental contact which could cause electric shock or burns. It must also be housed in a way that allows the heat generated to dissipate and do the job intended. For instance, a toaster needs a large aperture in which to place the bread so that it rests near the exposed element for it to function correctly. Read the rest of this entry »
Isolate the appliance before removing covers or panels for any reason. All tests for continuity should be carried out with a battery operated test meter only.
The most likely cause of overheating will be a failure of the thermostat contact points or sealed pressure system. In such a case you will need to fit a new compatible replacement unit.
Slow initial heating-up times or uneven heat distribution within the oven is usually caused by the failure of one element. Simple testing of the element will highlight the faulty item.
Failure to heat up at all may be either the thermostat or elements. As elements are the easier of the two to check for continuity, a simple process of elimination will indicate where the fault lies. Read the rest of this entry »
The information given here also applies to the grills on many cookers. This is a simple way to ascertain if the control is faulty. Short circuit failures on elements may damage regulators in which case, if you are in any doubt, renew it.
The following test is for a single circuit application, that is, a single element. For double regulators, that is, a double element, the same procedure will be required on both single and double operations of the switch. From off position an anticlockwise turn will put into circuit one element (usually the inner), a clockwise turn from the off position will put into circuit both inner and outer. Check that double regulators operate independently on a half turn each. For singles, use ony a full turn. Read the rest of this entry »
These are among the most frequently used items in the home. Generally, they are very reliable, but when a problem does occur, it is usually at the most inconvenient time. Over the years, ovens and hobs have become increasingly complex with the addition of digital timers, touch controls and other refinements.
It is essential to remember that these appliances are connected directly to the mains supply and, as with any repair, cleaning or service, must be completely isolated. In this instance, the main double-pole isolation switch for the appliance must be switched off and also the fuse for the cooker/hob circuit removed from the main distribution board. If an MCB is fitted in place of a fuse, ensure it is in the off position. Do not proceed with any repair or service if both these requirements are not met and also make sure you advise others who may use the switch of your intentions. Read the rest of this entry »
