A final condition that could cause weak pump-out is a loose drive belt that doesn’t rotate the water pump. A sure and quick check that involves no hand tools is to turn the timer knob to a cycle where there is a motor function such as spin or agitate. With the timer dial on spin cycle, the washer should begin to spin the clothes. If you hear the sound of the motor running, but the washer tub is not moving or attempting to spin the clothes, then it can be assumed that the washer drive belt is slipping on the drive motor pulley or the belt is broken. Read the rest of this entry »
Unplug the washer power cord before servicing automatic washer. Exercise care when moving washer from its original position, or the washer legs might damage the floor. To Replace Water Inlet Valve
To remove a water inlet valve, you must first turn OFF the hot and cold water at the wash station. Remove the two fill hoses with water pump pliers. Read the rest of this entry »
If the timer contact terminals show continuity and you find no voltage at the temperature selector switch, then you must make a continuity check for burned or broken wires from the timer assembly to the temperature selector switch. With the volt/ohmmeter dial set on the RX-1 scale, disconnect one wire from the terminal of the selector switch and attach a probe. Touch the remaining probe to the other end of same wire. If the wire you are checking is good, continuity (0 ohms) will be measured on the volt/ohmmeter. Read the rest of this entry »
Specific failure symptoms include: 1) Washer fills with water, and motor starts to run, but the washer agitator does not turn in either a clockwise or counterclockwise direction, or 2) At end of cycle, clothes are gritty and soapy with water.
To find the cause of the problem, first check to make sure that the washer power cord has not worked loose in the wall socket. Read the rest of this entry »
Next, check the dryer cycling thermostats as the possible cause for no heat in the dryer. The types of thermostats most commonly used in dryers (gas or electric), are the bimetal fixedand adjustable thermostats. Their primary function is to break the circuit to the gas main burner or the heating element when a certain temperature has been attained in the dryer drum. You can easily check these thermostats by removing one lead from the suspected thermostat. Set the volt/ohmmeter on the RX-1 scale. Place one probe of the volt/- ohmmeter on each terminal of the thermostat. You should see a continuity reading on the volt/- ohmmeter scale of approximately 0 ohms, or full- meter deflection. If the thermostat does not show continuity, replace the defective thermostat to restore the dryer to proper operating order. Read the rest of this entry »
Unplug the power cord or gas supply before servicing the clothes dryer. Move clothes dryer out from the wall. Exercise care when moving the dryer from its original position because the dryer legs can easily tear holes in your floor.
Remove screws to dryer top. Lift the top of the dryer by inserting a flat-blade screwdriver between the cabinet and the top of the dryer. Remove the screws that secure door switch to dryer front panel and discard the door switch. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use extreme care when moving the Fridge, because the Fridge legs can easily damage the floor.
Open the Fridge door and locate the control console in the back of the Fridge cabinet. Remove the screws that secure the console cover. Remove the thermostat bracket. NOTE: Before removing the defrost timer from the Fridge cabinet, mark the wires, so they can be replaced correctly on the replacement part. Next, remove the screws that secure the defrost timer to the Fridge cabinet. Next, remove wiring harness and remove defrost timer. Read the rest of this entry »
Unplug the fridge power cord before servicing the fridge. Move the fridge out from the wall. Use extreme care when moving the fridge, because the fridge legs can tear or damage the floor.
Using hand tools, remove the screws on all four sides of the fridge or freezer doors so that you can remove and discard the defective gasket(s). Before removing the old gasket, note carefully how the gasket is installed, because the replacement gasket has to be installed in the same position as the defective gasket that is removed. Before installing the replacement gasket, heat the rubber with a home hair dryer set on low heat. This will make the rubber more flexible,’ and easier to install on the fridge or freezer door. Install the replacement door gasket by mounting the lip of the gasket under the retainer plate. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use care when moving the Fridge, because the metal feet can tear or damage the floor.
Open the freezer door and remove the plastic breaker strips at the front of freezer section. NOTE: When removing plastic breaker strips, heat them with a low- wattage (40-60) light bulb for 5 to 7 minutes. Heat will make the plastic more pliable and less susceptible to breakage. Read the rest of this entry »
Unplug refrigerator power cord. Using hand tools, remove the icemaker from the freezer section of the refrigerator. Remove the front cover from the icemaker. Remove the front component plate that is secured to the ice maker support housing. Remove the screws that secure the cycling thermostat to the icemaker support.
Remove electrical wires from the terminals on the support housing, and carefully remove the thermostat. Read the rest of this entry »
