Specific failure symptoms include: 1) When the washer is turned ON, nothing happens. 2) When the washer is turned ON you hear a faint “buzz.”
To find the cause of this problem, first check to be sure that the washer is plugged in a working power source.
Make a line voltage check at the washer receptacle to determine if the problem is a faulty power receptacle or a problem within the washer. Make a voltage line check by setting the volt/ohmmeter on the 150 A/C scale and placing the probes in the holes of the wall receptacle. The meter should read 110-125 volts. Read the rest of this entry »
If the heating element tests OK, you should next check all the electrical wiring from the dryer timer assembly, thermostats, and drive motor. Electrical wiring in a dryer becomes brittle and burned because of the excessive heat. To locate defects in the wiring, use a volt/ohmmeter to make continuity checks on wires that you suspect are faulty.
The problem of no heat in the gas dryer is much the same as the electric dryer, except that instead of checking for a possible defective heating element, you must check the gas ignition circuit. A sure and simple test is check voltage to the gas burner wiring harness. Read the rest of this entry »
Specific failure symptoms include: 1) Clothes are not dry at end of cycle. 2) The dryer timer assembly is not advancing in the cycle properly.
To find the cause of the problem, first move the dryer out from the wall and remove the vent hose. With the dryer running, place your hand on the dryer exhaust duct to determine if there is any hot air being discharged. If the air is cold, you will have to make a line voltage check at the dryer receptacle to determine whether full 220-to-240-volt power is available. Read the rest of this entry »
An obvious failure symptom is when you select a drying cycle and attempt to start the dryer, but it does not run. To find the cause of the problem, move the dryer out from its position and unplug the power cord.
If line voltage is indicated on the volt/- ohmmeter, check the dryer power cord as possible cause of the problem.
To avoid any incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter before making continuity checks on components. Read the rest of this entry »
There are three types of failures that are associated with the Fridge start capacitor. These failures are a defective capacitor. an open filament capacitor, and a grounded capacitor. You can check each of the above failures with the volt/ohmmeter. First, unplug the Fridge power cord. Using hand tools, remove the screws that secure the Fridge back and remove the starting capacitor from the compressor starting package. Look for traces of oil on or around the capacitor. If oil is present, the capacitor is defective.
CAUTION: A charged capacitor is extremely dangerous. A capacitor that has been removed from the compressor starting package will hold a charge indefinitely, even when not in use. If you touch the terminals of a charged capacitor, the built-up voltage could give a high-voltage shock that could be fatal. A flat-blade screwdriver across the terminals should be used to discharge a capacitor. Read the rest of this entry »
Other specific symptoms include: 1) Food not remaining at desired temperature. 2) Compressor does not cycle ON.
Because the interior light is ON, the Fridge has the required electric power to operate.
Something is causing the compressor not to cycle ON. Check the components in the order that they are listed below. The most likely component at fault is the defrost timer, which could be stuck in the defrost cycle. The Fridge is then in a permanent state of defrost and does not cycle ON. However, if the compressor tries to start and the interior light dims, the problem is probably not the defrost timer or the thermostat; therefore, check the components of the compressor assembly starting with the starting relay. Read the rest of this entry »
Unplug refrigerator power cord, open the refrigerator freezer door, locate the compact icemaker and place your hand on the ejector blade. Turn it slowly in a clockwise direction. If the icemaker ejector blade continues to turn unaided, the problem is a defective icemaker holding switch. The icemaker holding switch can be checked with the volt/ohmmeter. First, set the ohmmeter to the RX-1 scale. Next, place the probes of the volt/ohmmeter on the terminals of the holding switch. With the switch button depressed, you should see full-scale deflection (continuity), on the scale of the volt/ohmmeter. No reading on the ohmmeter means the holding switch is open and must be replaced. Read the rest of this entry »
Next in line after the water supply valve is the water inlet valve, usually located at the back of the machine near the bottom. The role of the water inlet valve is to release supply water from the supply line so that it can enter the icemaker mold cavity. However, the valve’s internal components can eventually become worn out from the corrosive properties and algae in the water, and fail to supply water to the mold cavity. Check the water inlet valve to see if it is electrically releasing the water on command to the mold cavity. Read the rest of this entry »
Specific failure symptoms include: 1) Dishwasher has a full tub of water at the end of the cycle. 2) Dishwasher only partially drains and leaves water in tub at end of cycle.
Remove the lower panel. Locate the pump drain hose and see if a kink in the hose is evident. If so, remove the kink and check the dishwasher for proper operation. If the dishwasher now pumps the water out, you found the problem — a kinked drain hose. If little or no water is being pumped out, the problem is in the dishwasher pump assembly. Read the rest of this entry »
This is very important if you have a fridge with a built in deep-freeze compartment and not so if you have a frost-fee fridge. You know that feeling when you’re desperately trying to get to that last little ice cream lying in the back of the compartment and end up wrecking the ice compartment’s door because it won’t open?
When more than 10 mm of ice has accumulated it’s time to defrost. If the fridge has a defrost setting, engage it, or simply switch off the fridge. Some fridges can take up to 24 hours to defrost completely; consult the manufacturer’s instruction manual. Read the rest of this entry »
