Unplug the washer power cord before servicing automatic washer. Exercise care when moving washer from its original position, or the washer legs might damage the floor. To Replace Water Inlet Valve
To remove a water inlet valve, you must first turn OFF the hot and cold water at the wash station. Remove the two fill hoses with water pump pliers. Read the rest of this entry »
If the timer contact terminals show continuity and you find no voltage at the temperature selector switch, then you must make a continuity check for burned or broken wires from the timer assembly to the temperature selector switch. With the volt/ohmmeter dial set on the RX-1 scale, disconnect one wire from the terminal of the selector switch and attach a probe. Touch the remaining probe to the other end of same wire. If the wire you are checking is good, continuity (0 ohms) will be measured on the volt/ohmmeter. Read the rest of this entry »
Specific failure symptoms include: 1) Washer fills with water, and motor starts to run, but the washer agitator does not turn in either a clockwise or counterclockwise direction, or 2) At end of cycle, clothes are gritty and soapy with water.
To find the cause of the problem, first check to make sure that the washer power cord has not worked loose in the wall socket. Read the rest of this entry »
Next, check the dryer cycling thermostats as the possible cause for no heat in the dryer. The types of thermostats most commonly used in dryers (gas or electric), are the bimetal fixedand adjustable thermostats. Their primary function is to break the circuit to the gas main burner or the heating element when a certain temperature has been attained in the dryer drum. You can easily check these thermostats by removing one lead from the suspected thermostat. Set the volt/ohmmeter on the RX-1 scale. Place one probe of the volt/- ohmmeter on each terminal of the thermostat. You should see a continuity reading on the volt/- ohmmeter scale of approximately 0 ohms, or full- meter deflection. If the thermostat does not show continuity, replace the defective thermostat to restore the dryer to proper operating order. Read the rest of this entry »
Unplug the power cord or gas supply before servicing the clothes dryer. Move clothes dryer out from the wall. Exercise care when moving the dryer from its original position because the dryer legs can easily tear holes in your floor.
Remove screws to dryer top. Lift the top of the dryer by inserting a flat-blade screwdriver between the cabinet and the top of the dryer. Remove the screws that secure door switch to dryer front panel and discard the door switch. Read the rest of this entry »
Specific failure symptoms include: 1) An unusual smell in the laundry room. 2) The top of the dryer is very hot to the touch. 3) The clothes are extremely hot and wrinkled at the end of the cycle.
When a dryer is overheating, the first concern should be whether the heater element is cycling (turning ON and OFF). An easy check is to set the heat selector to a heat position and turn the timer to the ON position. With the dryer running, turn the overhead lights OFF. Check the back of the dryer (with the back panel removed). On left-hand side of cabinet there should be a visible glow from the heater box. This glow would indicate that the dryer is heating and has the required voltage. After a period of four to six minutes, the heater should cycle off and the glow should fade. If not, then probably the dryer cycling thermostats or adjustable thermostat is not functioning properly. You will have to replace the defective thermostat(s) in order for the dryer to operate properly. Read the rest of this entry »
Specific failure symptoms include: 1) The clothes dryer is running longer than normal. 2) The clothes are extremely damp at the end of the drying cycle.
Although the problem could be that the automatic washer is not spinning your clothes properly, in most cases the problem is inadequate air movement in the dryer.
Before blaming the dryer, you should check the automatic washer. At the end of the spin cycle, open the washer lid and check to see if there is excess water left in the washer basket. Read the rest of this entry »
Specific problems include: 1) The clothes dryer has excessive noise while running. 2) The clothes dryer stops in cycle. 3) The clothes are extremely damp when removed from the dryer drum at end of cycle.
All of the above symptoms are related to mechanical problems which develop from years of use.
Check the clothes dryer drum belt for excessive play or a stretched condition. A drum belt that is excessively stretched will cause the idler pulley to bang against the drum, resulting in excessive noise. In order to restore the dryer to proper operating order, you will have to replace the drive belt. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use extreme care when moving the Fridge, because the Fridge legs can easily damage the floor.
Open the Fridge door and locate the control console in the back of the Fridge cabinet. Remove the screws that secure the console cover. Remove the thermostat bracket. NOTE: Before removing the defrost timer from the Fridge cabinet, mark the wires, so they can be replaced correctly on the replacement part. Next, remove the screws that secure the defrost timer to the Fridge cabinet. Next, remove wiring harness and remove defrost timer. Read the rest of this entry »
There are three types of failures that are associated with the Fridge start capacitor. These failures are a defective capacitor. an open filament capacitor, and a grounded capacitor. You can check each of the above failures with the volt/ohmmeter. First, unplug the Fridge power cord. Using hand tools, remove the screws that secure the Fridge back and remove the starting capacitor from the compressor starting package. Look for traces of oil on or around the capacitor. If oil is present, the capacitor is defective.
CAUTION: A charged capacitor is extremely dangerous. A capacitor that has been removed from the compressor starting package will hold a charge indefinitely, even when not in use. If you touch the terminals of a charged capacitor, the built-up voltage could give a high-voltage shock that could be fatal. A flat-blade screwdriver across the terminals should be used to discharge a capacitor. Read the rest of this entry »
