Most popular SLR cameras have a fixed focusing screen and pentaprism, both of which are more than adequate for day to day situations. Although both of these features make rapid focusing and composition easier, neither can be the perfect answer in every situation. For that reason many photographers choose an SLR with an interchangeable focusing screen, viewfinder, or both. You will find that some of the more expensive cameras have this facility. Read the rest of this entry »
A final condition that could cause weak pump-out is a loose drive belt that doesn’t rotate the water pump. A sure and quick check that involves no hand tools is to turn the timer knob to a cycle where there is a motor function such as spin or agitate. With the timer dial on spin cycle, the washer should begin to spin the clothes. If you hear the sound of the motor running, but the washer tub is not moving or attempting to spin the clothes, then it can be assumed that the washer drive belt is slipping on the drive motor pulley or the belt is broken. Read the rest of this entry »
Unplug the washer power cord before servicing automatic washer. Exercise care when moving washer from its original position, or the washer legs might damage the floor. To Replace Water Inlet Valve
To remove a water inlet valve, you must first turn OFF the hot and cold water at the wash station. Remove the two fill hoses with water pump pliers. Read the rest of this entry »
Specific failure symptoms include: 1) Washer fills with water, and motor starts to run, but the washer agitator does not turn in either a clockwise or counterclockwise direction, or 2) At end of cycle, clothes are gritty and soapy with water.
To find the cause of the problem, first check to make sure that the washer power cord has not worked loose in the wall socket. Read the rest of this entry »
Unplug the power cord or gas supply before servicing the clothes dryer. Move clothes dryer out from the wall. Exercise care when moving the dryer from its original position because the dryer legs can easily tear holes in your floor.
Remove screws to dryer top. Lift the top of the dryer by inserting a flat-blade screwdriver between the cabinet and the top of the dryer. Remove the screws that secure door switch to dryer front panel and discard the door switch. Read the rest of this entry »
Specific failure symptoms include: 1) An unusual smell in the laundry room. 2) The top of the dryer is very hot to the touch. 3) The clothes are extremely hot and wrinkled at the end of the cycle.
When a dryer is overheating, the first concern should be whether the heater element is cycling (turning ON and OFF). An easy check is to set the heat selector to a heat position and turn the timer to the ON position. With the dryer running, turn the overhead lights OFF. Check the back of the dryer (with the back panel removed). On left-hand side of cabinet there should be a visible glow from the heater box. This glow would indicate that the dryer is heating and has the required voltage. After a period of four to six minutes, the heater should cycle off and the glow should fade. If not, then probably the dryer cycling thermostats or adjustable thermostat is not functioning properly. You will have to replace the defective thermostat(s) in order for the dryer to operate properly. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use extreme care when moving the Fridge, because the Fridge legs can easily damage the floor.
Open the Fridge door and locate the control console in the back of the Fridge cabinet. Remove the screws that secure the console cover. Remove the thermostat bracket. NOTE: Before removing the defrost timer from the Fridge cabinet, mark the wires, so they can be replaced correctly on the replacement part. Next, remove the screws that secure the defrost timer to the Fridge cabinet. Next, remove wiring harness and remove defrost timer. Read the rest of this entry »
Unplug the fridge power cord before servicing the fridge. Move the fridge out from the wall. Use extreme care when moving the fridge, because the fridge legs can tear or damage the floor.
Using hand tools, remove the screws on all four sides of the fridge or freezer doors so that you can remove and discard the defective gasket(s). Before removing the old gasket, note carefully how the gasket is installed, because the replacement gasket has to be installed in the same position as the defective gasket that is removed. Before installing the replacement gasket, heat the rubber with a home hair dryer set on low heat. This will make the rubber more flexible,’ and easier to install on the fridge or freezer door. Install the replacement door gasket by mounting the lip of the gasket under the retainer plate. Read the rest of this entry »
Unplug refrigerator power cord. Using hand tools, remove the icemaker from the freezer section of the refrigerator. Remove the front cover from the icemaker. Remove the front component plate that is secured to the ice maker support housing. Remove the screws that secure the cycling thermostat to the icemaker support.
Remove electrical wires from the terminals on the support housing, and carefully remove the thermostat. Read the rest of this entry »
Unplug refrigerator power cord, open the refrigerator freezer door, locate the compact icemaker and place your hand on the ejector blade. Turn it slowly in a clockwise direction. If the icemaker ejector blade continues to turn unaided, the problem is a defective icemaker holding switch. The icemaker holding switch can be checked with the volt/ohmmeter. First, set the ohmmeter to the RX-1 scale. Next, place the probes of the volt/ohmmeter on the terminals of the holding switch. With the switch button depressed, you should see full-scale deflection (continuity), on the scale of the volt/ohmmeter. No reading on the ohmmeter means the holding switch is open and must be replaced. Read the rest of this entry »
