Specific failure symptoms include: 1) Washer fills with water, and motor starts to run, but the washer agitator does not turn in either a clockwise or counterclockwise direction, or 2) At end of cycle, clothes are gritty and soapy with water.
To find the cause of the problem, first check to make sure that the washer power cord has not worked loose in the wall socket. Read the rest of this entry »
Next, check the dryer cycling thermostats as the possible cause for no heat in the dryer. The types of thermostats most commonly used in dryers (gas or electric), are the bimetal fixedand adjustable thermostats. Their primary function is to break the circuit to the gas main burner or the heating element when a certain temperature has been attained in the dryer drum. You can easily check these thermostats by removing one lead from the suspected thermostat. Set the volt/ohmmeter on the RX-1 scale. Place one probe of the volt/- ohmmeter on each terminal of the thermostat. You should see a continuity reading on the volt/- ohmmeter scale of approximately 0 ohms, or full- meter deflection. If the thermostat does not show continuity, replace the defective thermostat to restore the dryer to proper operating order. Read the rest of this entry »
If the heating element tests OK, you should next check all the electrical wiring from the dryer timer assembly, thermostats, and drive motor. Electrical wiring in a dryer becomes brittle and burned because of the excessive heat. To locate defects in the wiring, use a volt/ohmmeter to make continuity checks on wires that you suspect are faulty.
The problem of no heat in the gas dryer is much the same as the electric dryer, except that instead of checking for a possible defective heating element, you must check the gas ignition circuit. A sure and simple test is check voltage to the gas burner wiring harness. Read the rest of this entry »
Unplug the power cord or gas supply before servicing the clothes dryer. Move clothes dryer out from the wall. Exercise care when moving the dryer from its original position because the dryer legs can easily tear holes in your floor.
Remove screws to dryer top. Lift the top of the dryer by inserting a flat-blade screwdriver between the cabinet and the top of the dryer. Remove the screws that secure door switch to dryer front panel and discard the door switch. Read the rest of this entry »
An obvious failure symptom is when you select a drying cycle and attempt to start the dryer, but it does not run. To find the cause of the problem, move the dryer out from its position and unplug the power cord.
If line voltage is indicated on the volt/- ohmmeter, check the dryer power cord as possible cause of the problem.
To avoid any incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter before making continuity checks on components. Read the rest of this entry »
Specific failure symptoms include: 1) An unusual smell in the laundry room. 2) The top of the dryer is very hot to the touch. 3) The clothes are extremely hot and wrinkled at the end of the cycle.
When a dryer is overheating, the first concern should be whether the heater element is cycling (turning ON and OFF). An easy check is to set the heat selector to a heat position and turn the timer to the ON position. With the dryer running, turn the overhead lights OFF. Check the back of the dryer (with the back panel removed). On left-hand side of cabinet there should be a visible glow from the heater box. This glow would indicate that the dryer is heating and has the required voltage. After a period of four to six minutes, the heater should cycle off and the glow should fade. If not, then probably the dryer cycling thermostats or adjustable thermostat is not functioning properly. You will have to replace the defective thermostat(s) in order for the dryer to operate properly. Read the rest of this entry »
Specific failure symptoms include: 1) The clothes dryer is running longer than normal. 2) The clothes are extremely damp at the end of the drying cycle.
Although the problem could be that the automatic washer is not spinning your clothes properly, in most cases the problem is inadequate air movement in the dryer.
Before blaming the dryer, you should check the automatic washer. At the end of the spin cycle, open the washer lid and check to see if there is excess water left in the washer basket. Read the rest of this entry »
Specific problems include: 1) The clothes dryer has excessive noise while running. 2) The clothes dryer stops in cycle. 3) The clothes are extremely damp when removed from the dryer drum at end of cycle.
All of the above symptoms are related to mechanical problems which develop from years of use.
Check the clothes dryer drum belt for excessive play or a stretched condition. A drum belt that is excessively stretched will cause the idler pulley to bang against the drum, resulting in excessive noise. In order to restore the dryer to proper operating order, you will have to replace the drive belt. Read the rest of this entry »
Unplug the Fridge power cord before servicing the Fridge. Move the Fridge out from the wall. Use extreme care when moving the Fridge, because the Fridge legs can easily damage the floor.
Open the Fridge door and locate the control console in the back of the Fridge cabinet. Remove the screws that secure the console cover. Remove the thermostat bracket. NOTE: Before removing the defrost timer from the Fridge cabinet, mark the wires, so they can be replaced correctly on the replacement part. Next, remove the screws that secure the defrost timer to the Fridge cabinet. Next, remove wiring harness and remove defrost timer. Read the rest of this entry »
Unplug the fridge power cord before servicing the fridge. Move the fridge out from the wall. Use extreme care when moving the fridge, because the fridge legs can tear or damage the floor.
Using hand tools, remove the screws on all four sides of the fridge or freezer doors so that you can remove and discard the defective gasket(s). Before removing the old gasket, note carefully how the gasket is installed, because the replacement gasket has to be installed in the same position as the defective gasket that is removed. Before installing the replacement gasket, heat the rubber with a home hair dryer set on low heat. This will make the rubber more flexible,’ and easier to install on the fridge or freezer door. Install the replacement door gasket by mounting the lip of the gasket under the retainer plate. Read the rest of this entry »
