If the timer contact terminals show continuity and you find no voltage at the temperature selector switch, then you must make a continuity check for burned or broken wires from the timer assembly to the temperature selector switch. With the volt/ohmmeter dial set on the RX-1 scale, disconnect one wire from the terminal of the selector switch and attach a probe. Touch the remaining probe to the other end of same wire. If the wire you are checking is good, continuity (0 ohms) will be measured on the volt/ohmmeter. Read the rest of this entry »
Specific failure symptoms include: 1) Little or no water enters the washer. 2) The washer does I not complete the washing cycle. 3) The washer drive motor does not run during cycle. To find the cause of the problem, first check to be sure both the hot and cold water faucets are turned on at the wash station.
To avoid any incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter scale of the volt/ohmmeter before making any continuity checks on components. See operating instructions that came with the volt/ohmmeter. Read the rest of this entry »
This valve assembly is probably the most important component of the gas burner assembly. The valve assembly controls the flow of gas to the main burner from the gas supply line.
Cycling thermostats are bi-metal devices or thermo-discs that are designed to cut the main burner OFF when a pre-determined temperature has been attained in the dryer drum. There is no adjustment of the temperature response of these thermostats. Read the rest of this entry »
The home repairmen should be very cautious when it comes to repair of the household refrigerator. They should be aware of the fact that they are dealing with a very expensive product, and one that contains a very delicately balanced cooling system. One small error could damage the system beyond repair.
Replacing a faulty compressor requires special vacuum and freon filling equipment that only professional technicians can handle.
The refrigerator cooling system is not like the family automobile air conditioner. You can’t simply attach a hose and add a little freon when it isn’t cooling properly. The refrigerator is a carefully balanced, sealed system, and normally should not have a freon-loss problem. If the unit is not cooling properly, and you have determined that the compressor is running, then there are several electrical components in the system that could be at fault. Read the rest of this entry »
The components of a typical household refrigerator are described below:
The heart of the refrigerator system is the compressor. It is made up of a pump and an electric motor and is contained in a sealed dome through which the refrigerant travels.
The starting relayis an electromechanical switch used to start the compressor motor. As electricity flows, the starting relay energizes the start winding of the refrigerator compressor motor until the motor is almost up to speed. At this point, the relay breaks the electrical circuit to the start winding and the compressor motor continues to run on its run (or motor) winding. Read the rest of this entry »
Specific failure symptoms include either: 1) Refrigerator temperature too warm to make ice. 2) No water getting to icemaker mold. 3) Icemaker not ejecting the frozen ice.
For a compact icemaker to operate properly, the refrigerator freezer compartment must be maintained at 10 degrees F or lower. The design of the icemaker is such that the icemaker will not eject the ice until it is frozen hard. Read the rest of this entry »
Aschematic diagram of the internal workings of a pod-type thermostat. This type is used in appliances that have a variable temperature control. It consists of an oil-filled pod connected to the switch by a capillary tube. When the oil in the pod is heated or cooled, it expands or contracts in the tube and operates a diaphragm. The diaphragm acts on the switchgear thus breaking the circuit and in this instance, ‘making’ the other. The cooling oil contracts, pulling the switch the opposite way — back to its original position; the process repeats if temperatures change. Read the rest of this entry »
Many household appliances have some means of governing the temperature at which they operate. Examples include the regulation of high temperature ovens and heaters by switching elements on or off and, at the other end of the scale, the control of low temperatures in refrigerators and freezers by turning the compressor motor on or off.
A thermostat is an automatic device for regulating temperature. They range in type from the simple single action switch, which turns off or on at one pre-set temperature, to the fully adjustable type, which can be adjusted within a given range. Read the rest of this entry »
