When the solenoid is energized, the plunger is pulled upward by magnetic force of the solenoid coil, and the pin travels back and forth in the upper slot of the spin cam bar. This action pulls the spin cam bar backward from the basket clutch shaft, which allows the bar to slide downward toward the clutch lining. Read the rest of this entry »
Unplug the washer power cord before servicing automatic washer. Exercise care when moving washer from its original position, or the washer legs might damage the floor. To Replace Water Inlet Valve
To remove a water inlet valve, you must first turn OFF the hot and cold water at the wash station. Remove the two fill hoses with water pump pliers. Read the rest of this entry »
Specific failure symptoms include: 1) Washer begins to agitate or spin and water spills or leaks onto the floor. 2) After the washer has completed its cycle, water appears on the laundry room floor. To locate the cause of the problem, first look behind the washer at the wash station stand pipe. Check the washer water inlet valve, which has two hoses (hot-cold) attached, for deterioration of the hoses. If a hose has a leak, replace it.
To avoid any incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter scale of the volt/ohmmeter before making any continuity checks on components. See operating instructions. Read the rest of this entry »
Specific failure symptoms include: 1) Little or no water enters the washer. 2) The washer does I not complete the washing cycle. 3) The washer drive motor does not run during cycle. To find the cause of the problem, first check to be sure both the hot and cold water faucets are turned on at the wash station.
To avoid any incorrect readings when using the volt/ohmmeter, always “zero” the ohmmeter scale of the volt/ohmmeter before making any continuity checks on components. See operating instructions that came with the volt/ohmmeter. Read the rest of this entry »
Specific failure symptoms include: 1) When the washer is turned ON, nothing happens. 2) When the washer is turned ON you hear a faint “buzz.”
To find the cause of this problem, first check to be sure that the washer is plugged in a working power source.
Make a line voltage check at the washer receptacle to determine if the problem is a faulty power receptacle or a problem within the washer. Make a voltage line check by setting the volt/ohmmeter on the 150 A/C scale and placing the probes in the holes of the wall receptacle. The meter should read 110-125 volts. Read the rest of this entry »
The water supply that is controlled by a water inlet valve enters the mold cavity of the compact icemaker. The water then freezes in the icemaker mold. An electric heater thaws the frozen ice crescents so that they can be ejected from the mold. An electric motor then drives an ejector blade through a cam assembly, which frees the released crescents. The crescents revolve in a clockwise rotation and tumble into the ice storage bin. Read the rest of this entry »
Move the refrigerator out from the wall. Unplug the refrigerator power cord, and turn OFF the water supply to the icemaker.
Using hand tools, remove screws and discard the defective water supply valve. When installing a water supply valve on the water heater, install only on the cold-water side of the water heater. Read the rest of this entry »
Next in line after the water supply valve is the water inlet valve, usually located at the back of the machine near the bottom. The role of the water inlet valve is to release supply water from the supply line so that it can enter the icemaker mold cavity. However, the valve’s internal components can eventually become worn out from the corrosive properties and algae in the water, and fail to supply water to the mold cavity. Check the water inlet valve to see if it is electrically releasing the water on command to the mold cavity. Read the rest of this entry »
Specific failure symptoms include: 1) Water on floor near dishwasher. 2) During dishwasher cycle, water accumulates on left or right side of dishwasher lower panel.
To locate the cause of the problem, remove lower panel and check for broken plumbing drain connections, water inlet valve, broken or cracked hoses (drain and inlet), or drive motor and pump assembly motor seal. If a hose or a faulty part is found, replace it. Check that door is closing properly. Read the rest of this entry »
The heater elementis located in the tub cavity. It serves two functions during the dishwasher cycle: 1) The heat generated by the high-wattage element heats the water to a temperature of 140 degrees F. The water in the dishwasher tub has to be kept at this temperature or higher, so the hot water can dissolve the detergent. The dishes are thereby assured of being clean when they are removed from the dishwasher. 2) The element generates heat after the water is removed from the dishwasher. This heat helps dry the excess water that has accumulated on the dishes during the wash cycle. Read the rest of this entry »
